Settings

  • Important Tips

    When the ambient temperature is lower than 20 ℃ / 68℉, it is recommended that most RESIONE resins, except W90B and C01 resins, preheat (60-80 ℃ / 140-176℉, 10 minutes) before printing. If the printer is equipped with a heater, preheat for at least 30 minutes to ensure that the resin fluidity is good before printing. In addition, it is recommended to adjust the printing parameters (increase the "bottom lift distance" and "lifting distance", increase the "rest time after retract") to cope with the printing failure caused by the increase of resin viscosity.
  • Anycubic Photon Workshop V2.2.19 or Later

    • RESIONE resins settings for the following printers:

      (The above files are in zip file format, please unzip them first)

      We recommend that Anycubic printer users only select Anycubic Photon Workshop as a slicer for best printing results. Other slicer, such as Lychee, are not recommended because Lychee slicer is missing some setting options or function options of the Anycubic Photon Workshop, or the format of the slice file is incorrect. In addition, if you use the Chitbox slicer, the size of the prints will be smaller than the original model size, but Anycubic Photon Workshop slicer does not have this problem.

      How do I import settings file to Anycubic Photon Workshop?

      Download Anycubic Photon Workshop, install and open it.

      how to import resione resin settings file to anycubic photon workshop slicer
      how to import resione resin settings file to anycubic photon workshop slicer
      Some models only have the option [Basic], and the option [Advanced] cannot be selected. In this case, you can directly skip and click the option [Load]. As shown below:

      CHITUBOX V1.9.4 or CHITUBOX PRO V1.3.0 or Later

        RESIONE resins settings for the following printers:

        (The above files are in zip file format, please unzip them first)

        How do I import settings file to CHITUBOX Slicer?

        Download CHITUBOX and update the printer firmware ( Some older models of 3d printers may require firmware updates ), then install and open CHITUBOX.

        How to import RESIONE resins settings into chitubox

        Attention: We recommend that Anycubic printer users only select Anycubic Photon Workshop as a slicer for best printing results. If you use the Chitbox slicer, the size of the prints will be smaller than the original model size, but Anycubic Photon Workshop slicer does not have this problem.

        Lychee V5.0.0 or Later

          RESIONE resins settings for the following printers:

          (The above files are in zip file format, please unzip them first)

          How do I import settings file to Lychee Slicer?
          Download Import Guide

          Because Lychee slicer is missing some setting options or function options of the official slicer of the printer, or the format of the slice file is incorrect, so we only provide a few newly listed printers whose setting options or function options are identical with those of the official slicer. If you don't find the settings you need here, please replace the Lychee slicer with Anycubic Photo Workshop or Chitubox slicer for best printing results.

           

          UniFormation GKtwo Official Slicer

          How do I import settings file to GKtwo official slicer?

          Download RESIONE resins settings and import them into GKtwo official slicer.

          1

          Supports Settings For Flexible/Elastic Resin

            How do I import supports Settings file to CHITUBOX Slicer?

            Download files "support Settings 1"

            Download files "support Settings 2"

            Import the downloaded files to the CHITUBOX slicer as shown in the following figure

            Important:
            If you are using flexible/elastic resin, we recommend setting "Angle (°)" to 0.02, which can greatly improve the success rate of printing, as shown in the above figure.